Aspire NX75-Z TC Mod

The die-casted zinc alloy NX75-Z mod by Aspire features refined lines and high-level design accents throughout the design. The five button system is ultra-intuitive with one-button navigation between Temperature Control and Wattage mode. The Aspire NX75-Z can fire up to 75 watts and supports Nickel 200, Titanium, Stainless Steel 316, and TCR temperature control modes. The Aspire NX75-Z requires (1) high amp 18650 battery (sold separately) and may be replaced using the sliding magnetized battery door.

The NX75 series mods feature an all-new Customizable Firing Button Profiles (CFBP) function. CFBP allows for heat ramp-up (power curve) to be fine-tuned. This customization can be made with just a few button clicks. The NX75 allows you to customize your mod with just a few button clicks. Ease-of-Use is a key feature of the NX75. The NX75-Z also features a child lock system for extra safety precautions. Aside from firmware upgrades, all operations can be done with just a few click of the NX75-Z buttons. The Aspire NX75-Z also features a micro USB port for charging and future firmware updates.

Features and Specs:

  • Dimensions: 3″ x 1-7/16″ x 7/8″
  • Spring Loaded 510 Contact Pin
  • Wattage Range: 1W – 75W
  • Output Voltage Range: 0.00 – 8.5V
  • Temperature Control: Nickel 200, Titanium, Stainless Steel 316 and TCR
  • Temperature Control Range: 200 – 600F / 100 – 315C
  • Resistance Range: 0.1ohm – 3.5ohm
  • Requires (1) High Amp 18650 Battery (Sold Separately)
  • Customizeable Firing Button Profiles (CFBP)
  • High Resolution 0.86″ OLED Display Screen
  • Sliding Magnetized Battery Door
  • Zinc Alloy Construction
  • Child Lock System
  • Customize your Logo
  • Stealth Mode
  • Micro USB Charging Port
  • Firmware Upgradeable
  • Automatic Cut Off Protection
  • Short Circuit Protection
  • Low Resistance Protection
  • Overheat Protection
  • Overcharge Protection
  • Overdischarge Protection

This device should only be used with rechargeable Lithium Ion IMR batteries with an amp limit of 20A or higher. Using other batteries can be potentially hazardous.

Package Contents:

  • 1 x Aspire NX75-Z Mod
  • 1 x Micro USB Cable

Pioneer4you IPV400 200W TC Box Mod

The Pioneer4you IPV400 200W TC Box Mod is an advancement in output technology, integrating a proprietary chipset capable of firing up to 200W, versatile temperature control regulation including the SX Pure heating element, powered by dual 18650 batteries in a slim form factor that prides itself as one of the smallest 200W devices to date. The IPV 400 200W architecture is milled with a combination of natural contour shape to fit comfortably in hand with colorful wavelike accents to create a visually striking impression, measuring at 88mm by 41.5mm by 28mm. It structural design features an innovative three-button control, with the firing mechanism in the side panel of the device while the dual adjustment buttons are located directly next to the intuitive OLED display (similar to the Sigelei 213W) for overall user comfortability. The IPV 400 is integrated with a firmware upgradeable high-performance YiHi SX330-F4 chipset, featuring output range up to 200 Watts, minimum atomizer resistance of 0.05ohm, and dynamic temperature control regulation to pair with practically any RDA, RTA, and Sub-Ohm Tank. The finely-tuned temperature control suite with TCR setting support four distinct heating elements, such as Ni200 Nickel, Titanium, Stainless Steel, and a newly introduced SX Pure heating element. An everyday workhorse device with remarkable small form factor, ample power and range, and a beautifully-crafted chassis, the Pioneer4you IPV400 200W TC Box Mod makes for the perfect compact output platform.

Pioneer4you IPV400 200W TC Box Mod:

  • Dual 18650 High-Amp Battery – Not Included
  • Latest YiHi SX330-F4 Chipset Technology
  • Maximum Wattage Output: 200W
  • Minimum Atomizer Resistance: 0.05ohm
  • Temperature Control Range: 212-572F
  • “Smallest Size, Largest Power”
  • Soft Curvature Structure
  • Colorful Wavelike Accents
  • Intuitive OLED Display
  • Temperature Control Functionality
  • Compatible with Ni200 Nickel, Titanium, and SS304
  • Supports SX Pure Heating Elements
  • Temperature Control of Resistance (TCR) Setting
  • Magnetic Battery Door Cover
  • Low Voltage Protection
  • Low Resistance Protection
  • High Input Voltage Warning
  • Short-Circuit Operation
  • Reverse Battery Protection
  • 510 Connection

Includes:

  • 1 Pioneer4you IPV 400 Box Mod
  • 1 MicroUSB Cable
  • Instruction Manual

In order to use temperature control feature, it requires use of nickel, titanium, or stainless steel coils and must be built with non-resistant wire.

Eleaf iStick TC200W Box Mod

Eleaf is proud to introduce the next big thing, the iStick TC200W Box Mod. Just like the Wismec Reuleaux RX200 Mod, this powerful device requires (3) High Amp 18650 Batteries (Sold Separately) to fully power the iStick TC200W device. The Eleaf iStick TC200W mod can fire up to 200 watts and supports Nickel, Titanium, Stainless Steel wire and TCR in temperature control mode. The iStick TC200W mod features a innovative streamlined shape with a metallic finish that fits comfortably in your hand. The Eleaf iStick TC200W Box Mod utilizes an innovative flip-open battery cover for easy access to your batteries. With the high wattage capability, upgradeable firmware and multiple protection features, the Eleaf iStick TC200W is sure to provide a hard-hitting vaping experience for a long time.

Please note, the Eleaf iStick TC200W requires (3) High Amp 18650 Batteries and are sold separately.

Features and Specs:

  • Dimensions: 3-1/4″ x 2-1/4″ x 1-1/2″
  • Spring-loaded Contact Pin
  • Stainless Steel 510 Threads
  • Variable Wattage Range: 1.0W – 200.0W
  • Temperature Control: Nickel (Ni200), Titanium (Ti), Stainless Steel (SS316), TCR Modes
  • Temperature Adjustment Range: 100-315°C / 200-600°F
  • Resistance Range for Temperature Control: 0.05 – 1.5 ohm
  • Resistance Range for Variable Wattage: 0.1 – 3.5 ohm
  • Requires (3) High Amp 18650 batteries (Sold Separately)
  • **All (3) batteries must be the same brand and model. Discharge and recharge the (3) batteries together for maximum efficiency**
  • **We recommend an external charger for optimal charging**
  • OLED Display Screen
  • Innovative Flip-Open Battery Cover
  • Micro USB Charging Port
  • Upgradable Firmware
  • Stealth Function
  • Dual Circuit Protection
  • No Atomizer Protection
  • Atomizer Short-Circuit Protection
  • Atomizer Low Alert
  • Low Voltage Protection
  • Temperature Protection
  • Temperature Alert
  • Weak Battery Alert
  • Imbalanced Alert
  • Check Battery Alert
  • Charge Error Alert
  • Check USB Alert

Please note: Temperature control requires the use of nickel, titanium, or stainless coils.

Package Contents:

  • 1 x Eleaf iStick TC200W Box Mod
    1 x Micro USB Cable

Smok Alien 220W Mod Kit with TFV8 Baby Beast Tank

Smok Alien 220W Mod Kit with TFV8 Baby Beast Tank

SMOK presents the new 220W Mod Kit with the TFV8 Baby Beast Tank! Equipped with an oversized OLED display, 220 watts of max power, ergonomic design and lateral firing button, the Alien 220W is one of a kind! The Alien 220W mod runs on a dual series 18650 battery configuration (batteries sold separately). Batteries are installed via the bottom panel for convenience! The sexy carbon fiber inlays offer a sophisticated touch as well as an aggressive and powerful look.

The SMOK Alien 200W Kit features the TFV8 Baby Beast tank to complete the ultimate mod kit! The TFV8 Baby Beast brings the superior performance of the SMOK TFV8 Cloud Beast Sub Ohm Tank in a smaller 22mm format tank atomizer! Experience the unrivaled flavor and vapor production the TFV8 line has to offer in the Micro version! The TFV8 Baby Beast offers dual adjustable airflow to cool the 0.2ohm V8 Baby-Q2 Core (installed) and the 0.15ohm V8 Baby-X4 Core Coils (also included) so you can beast out on the low! You can vape as high as 80W on these coil heads with a recommended “best” wattage setting at 40-60W. There is no need to wrap any coils to get huge clouds and great vape! Simply prime your V8 coil heads and fill up the Baby Beast via the signature SMOK top juice fill feature!

SMOK Alien 220W Mod Features:

  • Wattage Power Range: 6W – 220W
  • Temperature Control Range: 200°F – 600°F / 100°C – 315°C
  • Voltage Range: 0.35V – 8V
  • 0.1Ω – 3.0Ω (VW Mode)
  • 0.06Ω – 3.0Ω (TC Modes)
  • Compatible TC Wires: Ni200, Titanium, Stainless Steel
  • Large OLED Display
  • Individual Battery Level Display
  • Micro USB Port (Charging & Upgrading)
  • Ergonomic Design
  • Lateral Fire Button
  • Spring Loaded 510 Pin
  • Requires (2) 18650 Batteries (Batteries Sold Separately)
  • Sliding Battery Door
  • Firmware Upgradeable
  • Dimensions: 44*30*85mm

SMOK TFV8 Baby Beast Tank Features:

  • 22mm Diameter Tank
  • 3ml Juice Capacity
  • Massive Dual Adjustable Airflow
  • Signature Easy Top Fill Feature
  • Removable 510 Delrin Drip Tip
  • Large Diameter Coil Options
  • Q2 and X4 Coil Heads Rated at up to 80W
  • Q2 and X4 Recommended at 40W-60W
  • 510 Compatible

Smok Alien 220W Mod Kit Package Contents:

  • (1) Alien 220W Mod
  • (1) TFV8 Baby Beast Tank
  • (1) V8 Baby-Q2 Coil (0.2Ω Pre-Installed)
  • (1) V8 Baby-T8 Coil (0.15Ω)
  • (1) Replacement Glass Tube
  • (1) Micro USB Cable
  • (1) Sealing Pad
  • (2) Smok Silicone Vapor Bands
  • (5) Spare O-Rings
  • (1) User Manual
  • (1) Warranty Card
  • (1) Qualified Battery Card

SMOK Alien 220W TC Box MOD

Prepare yourself for Smok’s newest offering that has taken the vaping industry by storm. The Smok Alien 220W TC vape MOD provides the vaper with a powerful and comfortable experience that has the entire vaping industry excited. This form factor MOD has the cleanest lines and conveniently designed curvature for a smooth feel. Smok continues its mastery of the fire bar with a new balanced and ergonomically placed button. A refined chip set allows for pint point accuracy and well adjusted ohm readings. A beautiful OLED display combines all of Smok’s previous successes into one stacked flow screen that will inform you of your current voltage, ohms, amperage, mode, working temperature (PCB°C) and a puff counter. A dual battery life indicator offers unmatched accuracy and works to keep the vaper well informed as to when a recharge of batteries is needed. Not only is the Smok Alien an accurate device but it also provides a smoldering 220 Watts of power. This mod allows the vaper to chose between variable wattage and temperature control modes for a wide variety of coil types. Powered by two 18650 batteries, this innovative vaporizer allows for the user to gain greater control and an unmatched tank or RDA vaping experience.

What’s Included:

  • 1 x Alien 220W Mod
  • 1 x Micro USB Cable
  • 1 x User Manual
  • 1 x Warranty Card

Specs & Features

  • Dimensions: 44*30*85mm
  • Wattage Range: 6W – 220W
  • Temperature Range: 200°F – 600°F / 100°C – 315°C
  • Voltage Range: 0.35V – 8V
  • Resistance Range:
    • 0.1Ω – 3.0Ω (VW Mode)
    • 0.06Ω – 3.0Ω (TC Modes)
  • Compatible TC Wires: Ni200, Titanium, Stainless Steel
  • Large OLED Display
  • Individual Battery Level Display
  • Micro USB Port (Charging & Upgrading)
  • Ergonomic Design
  • Lateral Fire Trigger
  • Spring Loaded 510 Pin
  • Requires (2) 18650 Batteries (Batteries Sold Separately)
  • Sliding Battery Door
  • Firmware Upgradeable

Sigelei 150W Temp Control Box Mod

Introducing the Sigelei 150W Temperature Control Box Mod, which is the second line after releasing the 75 Watt, is an advanced and high performance device that pack with many great features

Sigelei 150W TC Box Mod has the temperature range from 212 to 572.

The body is made out of aluminum alloy like the previous 150 watt box mod.

The wattage range will be between 10W to 150W. If you love to sub-ohm, the lowest atomizer resistance that it can go down to is 0.1ohm.

Sigelei 150W Temperature Control Box Mod Features:

  • Dimensions: 103*57*25 (mm)
  • Weight: 190g
  • Temperature range: 100°C – 300°C and 212°F – 572°F
  • Output wattage: 10W – 150W
  • Output voltage: 1.0V – 7.5V
  • Atomizer resistance: 0.1ohm – 3.0ohm
  • Battery voltage: 6.4V – 8.4V
  • Joule Range: 10J – 100J
  • Maximum current: 35A
  • Battery life readout in real time
  • Made out of aluminum alloy
  • Dual 18650 Battery (not included, can be purchased separately)
  • 510 spring loaded connection
  • No charging port
  • Magnetic battery door
  • Low voltage protection
  • Low resistance protection
  • Input high voltage warning
  • Output short-circuit protection
  • Reverse battery protection
  • Overheating prevention
Recommend that you use batteries with 30A or higher for this device.
This product is for advanced user only! Please have a great understanding and technical knowledge on how to use this product in order to properly use it. Use it at your own risk!

Kanger KBOX 200W Temp Control Mod

Kanger KBOX 200W Temp Control Mod

Introducing the KBOX 200W TC Mod; Kangertech has taken a revolutionary leap with their KBOX series. The Kanger KBOX 200W TC Mod is one of the smallest devices on the market that can fire up to 200 watts. Using Kanger’s latest chipset they have been able to drastically improve the wattage output to 200W and have incorporated a Temperature Control Mode.

The KBOX 200W TC Mod now supports Nickel, Titanium, Stainless Steel and Ni-chrome wire in temperature control mode. It can also fire atomizers as low 0.05 ohms in Temperature control and 0.10 ohms in Wattage Mode.

The KBOX 200W TC Mod has a spring loaded 510 contact pin and utilizes dual 18650 high amp batteries. The device also features a micro USB port for charging and future firmware updates!.

The KBOX 200W TC Mod offers a powerful and versatile vaping experience in a small and portable device.

Features and Specs:

  • Dimensions: 3-1/4″ x 2-1/4″ x 7/8″
  • Spring-loaded 510 Contact Pin
  • Wattage output: 7-200W
  • Temperature Control : Ni / Ti / SS / Ni-chrome
  • Temperature Control Range: 100 – 315C / 200 – 600F
  • Resistance: 0.05 ohm or above for Ni/ Ti/ SS Wire
  • Resistance: 0.10 ohm or above for Ni-chrome Wire
  • LCD Display Screen
  • Zinc Alloy and Aluminum Alloy Construction
  • Requires (2) 18650 High Amp Batteries (sold separately)
  • Micro USB Port for DC 5V at 1.5A and future firmware updates
  • Micro USB Cable (sold separately)
  • PCB with unique serial number
  • 10 second cut off safety feature
  • High temperature protection
  • Reverse battery protection
  • Short circuit protection
  • Low battery warning
  • Over-discharge protection

Please note: Temperature control requires the use of nickel, titanium, stainless wire.


NOTE: Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode or burn if mishandled. Make sure the user has enough knowledge of Li-Ion rechargeable batteries in charging, discharging and assembly before use. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. We are not responsible for damage if there is any modification of the batteries/chargers in any form or shape (including pack making). We are not responsible for any damage caused by misuse or mishandling of Li-Ion batteries and chargers.

This device should only be used with rechargeable Lithium Ion IMR batteries with an amp limit of 20A or higher. Using other batteries can be potentially hazardous.

Package Contents:

  • 1 x Kangertech KBOX 200W TC Mod

Kangertech KBOX 120W Mod

Kanger KBOX 120W Temp Control Mod

Introducing the KBOX 120W TC Mod; Kangertech has taken a revolutionary leap with their KBOX series. Using Kanger’s latest chipset they have been able to drastically improve the wattage output to 120W and have incorporated a Temperature Control Mode.

The KBOX 120W TC Mod now supports Nickel, Titanium, Stainless Steel and Ni-chrome wire in temperature control mode. It can also fire atomizers as low 0.05 ohms in Temperature control and 0.10 ohms in Wattage Mode.

The KBOX 120W TC Mod has a spring loaded 510 contact pin and utilizes dual 18650 high amp batteries. The device also features a micro USB port for charging and future firmware updates!.

The KBOX 120W TC Mod offers a powerful and versatile vaping experience in a small and portable device.

Features and Specs:

  • Dimensions: 3-1/4″ x 2-1/4″ x 7/8″
  • Spring-loaded 510 Contact Pin
  • Wattage output: 7-120W
  • Temperature Control : Ni / Ti / SS / Ni-chrome
  • Temperature Control Range: 100 – 315C / 200 – 600F
  • Resistance: 0.05ohm or above for Ni/ Ti/ SS Wire
  • Resistance: 0.1ohm or above for Ni-chrome Wire
  • LCD Display Screen
  • Zinc Alloy and Aluminum Alloy Construction
  • Requires (2) 18650 High Amp Batteries (sold separately)
  • Micro USB Port for DC 5V at 1.5A and future firmware updates
  • Micro USB Cable (sold separately)
  • PCB with unique serial number
  • 10 second cut off safety feature
  • High temperature protection
  • Reverse battery protection
  • Short circuit protection
  • Low battery warning
  • Over-discharge protection


Please note: Temperature control requires the use of nickel, titanium, stainless wire.

NOTE: Use special caution when working with Li-ion cells, they are very sensitive to charging characteristics and may explode or burn if mishandled. Make sure the user has enough knowledge of Li-Ion rechargeable batteries in charging, discharging and assembly before use. Always charge in/on a fire-proof surface. Never leave charging batteries unattended. We are not responsible for damage if there is any modification of the batteries/chargers in any form or shape (including pack making). We are not responsible for any damage caused by misuse or mishandling of Li-Ion batteries and chargers.

This device should only be used with rechargeable Lithium Ion IMR batteries with an amp limit of 20A or higher. Using other batteries can be potentially hazardous.

Package Contents:

  • 1 x Kangertech KBOX 120W TC Mod

Wismec Presa TC100W Box Mod

The Wismec Presa TC100W Box Mod is newest revision of the Presa platform, featuring a larger profile that can naturally accommodate a single 26650 as well as with a sleeve adapter that allows you to use an 18650 battery, alongside an upgraded temperature control suite, and an expanded range of 1 to 100W of output. Following in line of the Presa platform and released in anticipation of the Wismec Inde Duo, the Presa TC100W features a 30mm bezel that follows the form factor of the aforementioned Inde Duo while having the visual styling and aesthetic to run 22mm diameter atomizers organically. The chipset features the newest of Wismec’s output technologies, with a base power output of 1 to 100W alongside a 0.1 to 3.5 ohm atomizer resistance range. Full temperature control capability features out of the box support for Ni200 Nickel, Titanium, and Stainless Steel 316 heating elements along with an adjustable TCR setting that allows for further tuning and compatibility in temperature output mode. The 0.96 OLED screen features a neatly organized information stack, showcasing all essential information along with a new PCB temperature sensor. The signature firing mechanism of the Presa series features an improved mechanism, while maintaining the mechanical locking switch to prevent accidental firing. The Presa TC100W is powered by a 26650 battery (sold separately) along with a sleeve adapter that allows for the use of a single 18650 battery (sold separately), making it a convenient, versatile output platform. With a new, extended range and the capability to be run utilizing two different types of batteries, the Wismec Presa TC100 Box Mod is an ergonomic and highly capable output device at a highly competitive price point.

Product Features:

  • 1 to 100W Output Range
    • 0.1 to 3.5 ohm Atomizer Resistance Range
    • 75W Output Recommended in 18650 Mode
  • Full Temperature Control Output
    • Ni200 Nickel
    • Ti Titanium
    • Stainless Steel 316
    • TCR Mode
    • 0.05 to 1.5 ohm Resistance Range
    • 200 to 600 Degrees Fahrenheit/100 to 315 Degrees Celsius
  • Magnetic Battery Cover
    • Naturally Runs 26650 Battery
    • Sleeve Adapter for 18650
    • Batteries Sold Separately
  • Safety Lock Switch
    • Mechanically Locks Switch Mechanism
  • OLED Screen
    • 0.96 Inches
    • Mode Display
    • Temperature Display
    • Power/Voltage Display
    • Real Time Resistance Readout
    • Real Time Current Readout
    • Battery Life/Puff Counter
  • Micro USB Charging Port
  • 510 Spring Loaded Connector
  • Ergonomic Firing Mechanism
    • Adjustment Buttons
  • Protection Features
    • Temperature Protection
    • 10 Second Protection
    • Short Circuit Protection
    • Low Resistance/Low Voltage/Low Battery Protection

Product Dimensions:

  • 93mm x 46mm x 30mm

Product Includes:

  • One Wismec Presa TC100W Box Mod
  • One Battery Sleeve Adapter
  • One Charging Cable
  • User Manual

Advanced User Item. Use AT YOUR OWN RISK!

SMOK Koopor Primus KP300TC

The KOOPOR Plus features Dual Driver System and HFDMR (High-Frequency Dynamic Monitoring Resistance) Technology, is one of the most accurate temperature-control mod ever made! It provides 200w maximum power, and takes dual 18650 batteries that can allow most vapors to enjoy vaping all day! Aside from superb performance, the KOOPOR Plus is the definition of fresh and aesthetic. It’s guaranteed to make heads turn!

 

Material: Stainless Steel and Zinc Alloy
Output Power: 6w-200w
Output Voltage: 0.35v-8.00v
Resistance Range: 0.08Ω—3.00Ω (Temp Mode)
0.10Ω—3.00Ω (Watt Mode)
Standby Current: < 300µA
Maximum Current: it should be less than 50A when the atomizer resistance is 0.1 ohm.
Temperature Control
Temperature protection between 200°F and 600°F(or 100°C-315°C)

Under temp mode, KOOPOR Plus can recognize your coils made of Ni200 alloy, Ti and SS.
Be careful to only attach new atomizers that have cooled to room temperature to the mod.
When using a new atomizer or reconnect your existing atomizer under temp mode, the KOOPOR Plus will prompt “NEW COIL UP SAME DOWN” to allow you to confirm the change.

eVic Basic

eVic Basic, being slim and cute in appearance applies variable Temperature Control system, supporting RTC (Real Time Clock) display function with clock screen protection. The eVic Basic combines unique and attractive styling with a super large OLED screen where RTC/VW/VT/Bypass/TCR modes can be regulated clearly with ease. Upgradable firmware always enables it up-to-date.

Standard Configuration:

  • 1 * eVic Basic Battery
  • 1 * USB Cable
  • 1 * User Manual
  • 1 * Warranty Card
  • 1 * Warning Card

Specification:

  • Size: 22.00*32.00*55.00mm
  • Battery Capacity: 1500mAh
  • Output Mode: RTC/VT (Ni/Ti/SS316)/VW/TCR/BYPASS Modes
  • Output Wattage: 1-40W
  • Resistance Range: 0.05-1.5ohm for VT/TCR mode
  • 0.1-3.5ohm for VW/BYPASS mode
  • Temperature Range: 100-315°C/ 200-600°F
  • Colors: Silver, Black, White, Red, Orange, Blue
Compact Yet Powerful
The eVic Basic comes with a tiny shape, which is quite easy to grip. It is powered by a 1500mAh built-in battery,
whose maximum output can be reached to 40W.

RTC (Real Time Clock) On Display

  • Dial display
  • Numeric display
  • Screen protection
Dual Circuit Protection
  • eVic Basic applies two sets of battery protection circuit system, realizing overall battery protection of
    over-charging, over-current and over-discharging, which makes it more safe and reliable.
Firmware Upgradeable
  • eVic Basic comes with the upgradeable firmware.
    Having the latest Version 4.02, new interface, multiple modes and functions are available.

Exquisite 510 Stainless Steel Thread

  • Applied with 510 stainless steel thread and wide border fitting for large capacity atomizers.
Bottom Ventilation Holes
  • The ventilation holes are placed on the bottom which can greatly help the device for better heat dissipation.
Charging & Upgrading
  • Simply connect the device with a micro USB cable to charge or upgrade your device. When it’s fully charged, the charging indicator will go out.

The LE80 Box Mod by Lotus

An absolute power house of a regulated box mod, this beast gives even the Jellyfish a run for its money! Taking two 18650 batteries, the LE80 has a specially designed chip that has several safety features that include not firing unless the battery is placed correctly. This is a variable voltage device and fires from about 3 volts to about 6 volts. If you build your coils to .2 ohms, then the LE80 will throttle the voltage and prevent it from firing. This protects your batteries and the internal components of the LE80. For the features and the power, this is a great piece of hardware for yourself or for a friend.

Fire Button

  • No fire length limitations
  • 0.2~5ohm
  • Spring loaded post with 510 Atomizer threading

Potentiometer

  • Twist to adjust voltage. Volt Range: 3.3v ~ 6v

3 Stage Switch

  • UP: Led waits to show current volts while vaping

Press Fire.

  • Middle: Turns the device off.
  • Down: LED shows the battery status.
  • 0% ~ 100% = 6.6v ~ 8.4v

LED Display

  • Voltage & battery status

Magnetic Cap

  • 2pcs 18650 battery compartment

LE80 Built In Safety Features

  • Auto Output Shutoff if unit’s core is > 120
  • Device will detect battery direction and
  • will not function if inserted incorrectly.

 

IJOYE Crebox C60 box mod kit

The Crebox is back however, the Crebox C60 takes a different path than the original! Utilizing an internal 1800mAh battery it is very compact and easily fits in a shirt pocket! It is capable of reaching up to 60 watts, supports temperature control, and has a minimum resistance of 0.10 ohms. Temperature control is compatible with Nickel, Titanium, and stainless steel wire to ensure that it is compatible with virtually all temperature control based coils. Included with your Crebox C60 is also the Vertice Tank! The included tank offers a 2.5mL liquid capacity, top filling design, and wide open adjustable airflow! For those that like portability and performance, you couldn’t pick a better device!

Note: Vertice Tank Coil is reverse threaded.

Crebox C60 Features:

  • Maximum Wattage Output: 60.0W
  • Battery: Internal 1800 mAh
  • Minimum Resistance: 0.10 ohms
  • Supports Nickel, Titanium, and Stainless Steel in Temperature Control
  • USB Charging
  • Rubberized matte finish
  • Low voltage protection
  • Short circuit protection
  • Low resistance protection

Vertice Tank Features:

  • 22mm Diameter
  • 2.5mL Tank Capacity
  • Adjustable Airflow
  • Top Fill Design

You Will Receive:

  • 1x – Crebox C60
  • 1x – Vertice Tank
  • 1x – Extra Kanthal Coil

The Crebox C60 Kit offers BEASTLY portability and performance due to its internal 1800mAh battery! Vape on the go with ease!

Kanger DRIPBOX Starter kit

Kanger Dripbox Starter Kit

Kangertech is once again setting a new trend in vaping technology with the Kanger Dripbox Kit. The Dripbox Kit features the “squonker” design or also known as a bottom feeder to provide a convenient dripper experience without the hassles of dripping. The Subdrip RDA features a juice delivery mechanism at the bottom of the 510 threads which allows e-liquid to saturate the cotton. E-liquid is simply squeezed/refilled using the e-liquid bottle located at the bottom of the device to saturate your cotton and is now ready to be vaped for massive flavor.

The Dripbox Kit features the Subdrip RDA and a Dripmod device all together in one convenient kit. The Subdrip RDA features 0.2ohm cotton drip coils which are easily replaced or can be rebuilt to your own personal preferences. The Subdrip RDA can also be filled from the top as well. The Dripmod device fires at a constant 60W and has a incredible capacity of 7ml due to the bottom feeding design. The Dripmod requires (1) 18650 High Amp Battery (sold separately) and features a Micro USB charging port.

The Dripbox Kit is matched with an incredible budget friendly price catering to all types of people. The Kanger Dripbox Kit is perfect for vapers looking to get that incredible dripper flavor without the hassles of constantly dripping and redripping.

NOTE: The Subdrip RDA and Dripmod device are not compatible with other devices or tanks due to the juice delivery system. Using other types of device or tanks may cause juice to flow down which may damage your device or battery.

Features and Specs:

  • Dimensions: 4-1/2″ x 1-3/4″ x 7/8″ (Including Subdrip RDA)
  • Includes the Subdrip RDA and Dripmod
  • 22mm Diameter
  • Bottom Feeding Design
  • Juice Delivery System
  • May also be Top-Filled
  • Wattage Output: 60W
  • Voltage Output: 3.7V
  • Minimum Resistance: 0.2ohm
  • 7ml e-Liquid Capacity
  • Use pre-built 0.2ohm drip coils or build your own
  • Adjustable Airflow
  • Subdrip RDA – Stainless Steel Casing
  • Dripmod – Aluminum Casing
  • Requires (1) 18650 High Amp Battery (Sold Separately)
  • Micro USB Charging Port
  • Low Resistance Protection
  • Reverse Battery Protection
  • Low Battery Warning Indicator

Rebuildable atomizer: The user of this atomizer must install wick and wire (coil) in order to use it. This atomizer is not pre-installed with coil. Installation is required. Wick, wire and mesh sold separately.


Important Note:
Rebuildable atomizer coils and wicks have known risks.

Rebuildables are for experts, not average or beginner vapers with no multimeter or knowledge of how to use a meter, or when a meter must be used, or how electronic devices work. These materials cannot safely be used by the inexperienced or those without basic knowledge of electronics.

This is because:

1. A rebuildable coil/wick MUST be tested carefully with a meter before it is used.
2. If it is not tested it is entirely the risk of the user.
3. Faulty wicks/coils WILL blow electronic devices.
4. New coil/wick units must be tested and then used first on a strong basic electrical APV that has short circuit protection.
5. No new coil/wick assembly should be used on an electronic device until known to be safe.
6. These items destroy electronic devices if faulty. This is a known issue.


Tip for new users: We strongly suggest 6mg eLiquid or lower with this atomizer. Sub-ohm atomizers produce higher throat hit than low and standard resistance atomizers. Using this atomizer with a nicotine level above 6mg will usually taste burnt or harsh.

This device should only be used with rechargeable Lithium Ion IMR batteries with an amp limit of 20A or higher. Using other batteries can be potentially hazardous.

Package Contents:

  • 1 x Kanger Dripmod Device
    1 x Subdrip RDA
    1 x Kanthal Cotton 0.2ohm Drip Coil (Pre-installed)
    1 x Replacement Kanthal Cotton 0.2ohm Drip Coil
    1 x Set of Spare Screws
    2 x Prebuilt Microcoils
    1 x Spare Bottle
    1 x Pad of Cotton
    1 x Micro USB Cable

Kanger Dripbox 160 Starter Kit

Features and Specs:

  • Dimensions: 4-3/4″ x 2″ x 1″ (Including Subdrip 160 RBA)
  • Includes the Subdrip 160 RBA and Dripbox 160 Mod
  • 22mm Diameter
  • Bottom Feeding Design
  • Juice Delivery System
  • Temperature Control
  • Top-Fill Option
  • Variable Wattage Output: 7.0 – 160.0W
  • Temperature Control : Ni200 / Ti / SS / Ni-Chrome
  • Temperature Control Range: 100 – 315C / 200 – 600F
  • Resistance: 0.05 ohm or above for Ni/ Ti/ SS Wire
  • Resistance: 0.10 ohm or above for Ni-chrome Wire
  • 7ml e-Liquid Capacity
  • Velocity Style Base for Rebuildable Coils
  • Use pre-built 0.2ohm drip coils or build your own
  • Subdrip 160 RBA – Stainless Steel Casing
  • Dripbox 160 – Zinc Alloy Casing
  • Requires (2) 18650 High Amp Batteries (Sold Separately)
  • Micro USB Charging Port
  • *External charger recommended for faster charging speeds*
  • Low Resistance Protection
  • Low Battery Warning Indicator
  • High Temperature Protection

Please note: Temperature control requires the use of nickel, titanium, stainless wire.


Rebuildable atomizer: The user of this atomizer must install wick and wire (coil) in order to use it. This atomizer is not pre-installed with coil. Installation is required. Wick, wire and mesh sold separately.

Rebuildables are for experts, not average or beginner vapers with no multimeter or knowledge of how to use a meter, or when a meter must be used, or how electronic devices work. These materials cannot safely be used by the inexperienced or those without basic knowledge of electronics.

This is because:

1. A rebuildable coil/wick MUST be tested carefully with a meter before it is used.
2. If it is not tested it is entirely the risk of the user.
3. Faulty wicks/coils WILL blow electronic devices.
4. New coil/wick units must be tested and then used first on a strong basic electrical APV that has short circuit protection.
5. No new coil/wick assembly should be used on an electronic device until known to be safe.
6. These items destroy electronic devices if faulty. This is a known issue.


Tip for new users: We strongly suggest 6mg eLiquid or lower with this atomizer. Sub-ohm atomizers produce higher throat hit than low and standard resistance atomizers. Using this atomizer with a nicotine level above 6mg will usually taste burnt or harsh.

Package Contents:

  • 1 x Kanger Dripbox 160 Device
    1 x Kanger Subdrip 160 RBA
    1 x Stainless Steel 0.25ohm Drip Coil (Pre-Installed)
    1 x Replacement Kanthal 0.2ohm Drip Coil
    1 x Spare Bottle
    1 x Accessory Pack
    1 x Pad of Cotton
    1 x Micro USB Cable

SMOK OSUB Plus 80W TC Starter Kit

The SMOK OSUB Plus 80W TC Starter Kit builds upon the original OSUB ecosystem, improving upon performance-driven out, fully-loaded chipset with power upgrade up to 80W combined with enlarged chassis and paired with the new Brit Beast Sub-Ohm Tank. The SMOK OSUB Plus features the ergonomic hand-friendly design, with a streamlined shape that features a lateral stealth C-Shaped firing bar. Integrated with an intuitive OLED screen with adjustment buttons and microUSB port directly below, convenience and highly ergonomic form factor is the marquee design. The chipset is highly dynamic, powered by a 3300mAh internal battery that fires up to 80W with a fully firmware upgradeable system, allowing for additional support and revisions. The OSUB Plus 80W implements comprehensive temperature control settings, with support for Ni200 Nickel, Stainless Steel, and Titanium heating elements. The Brit Beast Tank is a flavor-focused atomizer platform, featuring 510 V-Shape drip tip, bottom adjustable airflow system, 2mL with threaded top-fill, and utilizes the TFV8 Baby Beast’s Coil structure. With a compact and capable device paired with a capable sub-ohm tank, the SMOK OSUB Plus 80W TC Starter Kit is an affordable starter kit with fully-featured functionalities.

SMOK OSUB 80W TC Mod Features:

  • Dimensions: 75mm by 54.5mm by 22mm
  • Integrated 3300mAh Battery Capacity
  • Wattage Output Range: 1-80W
  • Voltage Output Range: 0.8-9V
  • Minimum Atomizer Resistance: 0.6ohm
  • Temperature Control Range: 200-600F
  • Supports Ni200, Titanium, and Stainless Steel Heating Elements
  • High Quality Zinc Alloy Construction
  • Intuitive OLED Side Screen
  • Stealth C-Shaped Lateral Firing Bar
  • Two-Button Adjustments
  • Intelligent Atomizer Recognition
  • Overheat Protection
  • Puff Monitoring System
  • 12 Seconds Cut-Off
  • Overheat Protection
  • Short-Circuit Protection
  • Low Battery Warning
  • 510 Connection


SMOK Brit Beast Sub-Ohm Tank Features:

  • 24.5mm Diameter
  • 3.5mL Juice Capacity
  • Superior Stainless Steel Construction
  • Pyrex Glass Reinforcement
  • Flavor-Focused Design
  • Threaded Top-Fill Method
  • Top Dual Adjustable Airflow System
  • Bullet Widebore Drip Tip
  • 510 Connection

In order to use temperature control feature, it requires use of nickel coils or titanium coils and must be built with non-resistant wire.

Do not use Ni200, Titanium, and Stainless Steel with non-temperature control devices/mods. This is a risk of battery explosion! Please make sure that the devices/mods that you are using is capable of controlling coil temperature.

Warning: This tank is a Sub-Ohm resistance atomizer and only work on mechanical mod or devices that can handle Sub-Ohm resistance of 0.5ohm or lower. Please make sure you have a great understanding and technical knowledge on how to use mods and batteries that can handle Sub-Ohm coils. Do not use short or flat 510 connection on any hybrid or hybrid style device. If you are not familiar or unsure of particular products or set-ups, please do not use it. Always use proper precautions and handling.

Note: When it comes to using RDA, RDTA, and RDTA, we strongly recommended to wash and clean all the atomizers thoroughly and carefully. Likewise, please have a great sense of knowledge when it comes to handling and using these products.

We always strongly recommend testing the coils with ohm-meter before using them with your mods, devices and batteries. Coils with low resistance are not suitable with all mods, devices and batteries. Please make sure that your mods, devices and batteries can handle low resistance before using them.

This product is for advanced user only! Please have a great understanding and technical knowledge on how to use this product in order to properly use it. Use it at your own risk!

 

Kangertech CUPTI 2 Starter Kit

The Kanger CUPTI 2 is an All-In-One device similar to the Aspire Plato and Kanger NEBOX that is designed for both mouth to lung and direct lung vapers. The Kanger CUPTI 2 features a large 5.0ml built-in tank that utilizes the acclaimed leak resistant cup design to help minimize leaks. The Kanger CUPTI 2 can fire up to 80 watts and supports Nickel 200, Titanium and Stainless Steel atomizers in temperature control mode. The Kangertech CUPTI 2 supports the CLOCC atomizer heads and includes (1) SS316L 0.5ohm atomizer head for direct lung users. The Kanger CUPTI also features an adjustable airflow valve located right under the mouth piece for maximum airflow.

The included 510 tank adapter allows you to use your favorite tank or dripper with the CUPTI 2. The Kanger CUPTI requires (2) high amp 18650 batteries (sold separately) and is easily replaced using the bottom battery door which is easily locked and unlocked. The CUPTI 2 has a micro USB port for charging and future firmware updates. All you require is batteries and e-Liquid and you are ready to start vaping!

Features and Specs:

  • Dimensions: 4-1/8″ x 2″ x 1-5/8″
  • All in One Design
  • Includes 510 Tank Adapter
  • Temperature Control for Nickel 200, Titanium and Stainless Steel
  • 5.0ml Capacity
  • Operating Wattage: 5.0 – 80.0 W
  • Temperature Range: 100 – 315C / 200-600F
  • Resistance Range: 0.1 – 2.5ohm
  • Top Adjustable Airflow Valve
  • Leak Resistant Cup Design
  • OLED Display Screen
  • Durable Surface Finish
  • Zinc and Aluminum Alloy Construction
  • 510 Drip Tip Compatible
  • Micro USB Charging Port
  • Firmware Upgradeable
  • Utilizes (2) High Amp 18650 Batteries (Sold Separately)
  • Utilizes Kanger CLOCC Atomizer Heads
  • Includes 1 x CLOCC SUS316L 0.5ohm Atomizer Head (Pre-Installed) for Direct Lung Users
  • Supports Optional CLRBA Rebuildable Atomizer (Sold Separately)

This device should only be used with rechargeable Lithium Ion IMR batteries with an amp limit of 20A or higher. Using other batteries can be potentially hazardous.

Warning: This tank uses sub-ohm resistance coils. This tank should only be used by experienced users. Extra safety precautions should be practiced when using a sub ohm tank. This tank will only work on a mechanical mod or a regulated mod capable of firing sub ohm atomizers and coils. For example, if you have a 0.2ohm coil, your mod must be able to fire atomizers of 0.2ohm or lower. You must be also ensure that your batteries can handle sub ohm atomizers and coils. If you’re using a regulated mod, make sure it can handle the amps. Improper use can lead to injury or damage. For mechanical mod users, please use 20 Amp batteries or higher.

Package Contents:

  • 1 x Kanger CUPTI 2
    1 x 510 Tank Adapter
    1 x Preinstalled CLOCC SS316L 0.5 ohm Coil
    1 x Micro USB Cable

SMOK GX350 Kit

Kits typically have a ton of components that can make it really difficult to choose from if you don’t know how certain devices work with one another, but with the Smok GX350 Kit, you get a kit that is destined for greatness! With this kit, you’ll have the GX 350 Mod as well as the Smok TFV8 Tank, bring you that winning combo you’ll be sure to love. This kit brings some serious flavor and cloud production and it’s something Smok has really put their heart and soul into. The design is incredible and you have a lot of color combos to choose from as well. Pick your favorite from the red/black, silver/black, gold/black, and purple/black kits. Powering these kits is pretty cool too because you can use them with 4 18650 batteries or 2 depending on how much power you want. With four batteries, you can blast up to 350 watts at your e-juice. If you decide to use two batteries, you’ll get 220 watts of vaping power! Regardless, either way you will have more than enough power so you’ll never feel underpowered! The Smok TFV8 Tank also comes with this kit, giving you the ability to hold up to 6mL of e-liquid. It’s also 510 threaded, meaning it can be used with other 510 threaded devices as well. When you have the Smok GX350 Kit, you have a kit that uses only the highest quality vapor-producing components available and you’ll taste the difference in your vapor!

 

GX 350 Mod Specifications:

  • Size: 58 x 40.4 x 84.5mm
  • Max Output Power: 350W (With 4 x 18650’s)
  • Perimeter: 151mm
  • 220W (With 2 x 18650’s)

Smok TFV8 Tank Specifications:

  • Weight: 74g
  • Material: Stainless Steel
  • Size: 24.5 x 69mm
  • Threading: 510
  • Capacity: 6mL

Package Contents:

1 x User Manual

1 Replacement Glass Tube

1 x Spare Parts Pack

1 x GX 350 Mod

1 x V8-Q4 Quadruple Coil Head (0.15Ω)

1 x TFV8 Tank

1 x V8-T8 Octuple Coil Head (0.15Ω)

SMOK Skyhook RDTA Box 220W Kit

The SMOK Skyhook RDTA Box is the next cutting-edge technology primed to storm the industry, presenting a high-performance output system with an integrated Skyhook RDTA that caters towards advanced builders and fully ergonomic form factor. The Skyhook 220W TC Box Mod features modernized resemblance to the highly anticipated Alien 220W, implementing a stealth firing bar painted with vibrant colors alongside a large OLED display matrix to provide extensive information within a user-friendly operational interface. More info to come.

SMOK Skyhook RDTA Box 220W Starter Kit:

  • All-In-One Design
  • Dimensions: 129mm by 50mm by 9mm
  • 9mL Built-in Skyhook RDTA Tank
  • Dual High-Amp 18650 Batteries – Sold Separately
  • Wattage Output Range: 6-220W
  • Voltage Output Range: 0.35-8V
  • Min Atomizer Resistance: 0.06ohm
  • Temperature Range: 200-600F
  • Supports Ni200 Nickel, Titanium, and Stainless Steel Heating Elements
  • Premium Stainless Steel Construction
  • Enlarged 0.96 Inch OLED Display Matrix – Highly Intuitive
  • Stealth Firing Bar Mechanism – Stunning Colors
  • Ergonomically Placed Adjustment Buttons
  • MicroUSB Port
  • Availabe in Silver, Black, Blue, Red, Gold, and White

SMOK Skyhook RDTA Tank Features:

  • 9mL Juice Capacity
  • Superior Stainless Steel Construction
  • Pyrex Glass Reinforcement
  • Enlarged 23.2mm Build Deck
  • Floating Velocity-Style Design – Two-Post Dual Terminal
  • 2.5mm Diameter Terminal Posts
  • Single Coil or Dual Coil Build Configurations
  • Convenient Side-Fill Port
  • Multiple Airflow System
  • Bottom-Middle Slotted Airflow Tube Sleeve
  • Middle Slotted Airflow Tube Sleeve
  • Delrin Widebore Drip Tip

Includes:

  • 1 Skyhook 220W Box Mod
  • 1 Preinstalled Skyhook RDTA Tank
  • 1 Extra Atomizer Tube for Middle Airflow
  • 1 MicroUSB Cable
  • Spare Parts
  • Instructional Manual

In order to use temperature control feature, it requires use of nickel coils or titanium coils and must be built with non-resistant wire. 

Do not use Ni200, Titanium, and Stainless Steel with non-temperature control devices/mods. This is a risk of battery explosion! Please make sure that the devices/mods that you are using is capable of controlling coil temperature.

Warning: This tank is a Sub-Ohm resistance atomizer and only work on mechanical mod or devices that can handle Sub-Ohm resistance of 0.5ohm or lower. Please make sure you have a great understanding and technical knowledge on how to use mods and batteries that can handle Sub-Ohm coils. Do not use short or flat 510 connection on any hybrid or hybrid style device. If you are not familiar or unsure of particular products or set-ups, please do not use it. Always use proper precautions and handling.

Note: When it comes to using RDA, RDTA, and RDTA, we strongly recommended to wash and clean all the atomizers thoroughly and carefully. Likewise, please have a great sense of knowledge when it comes to handling and using these products.

We always strongly recommend testing the coils with ohm-meter before using them with your mods, devices and batteries. Coils with low resistance are not suitable with all mods, devices and batteries. Please make sure that your mods, devices and batteries can handle low resistance before using them.

This product is for advanced user only! Please have a great understanding and technical knowledge on how to use this product in order to properly use it. Use it at your own risk!

Note: There is always an inherent risk when using any rechargeable batteries at anytime and under any circumstances. ElementVape.com and any of ElementVape.com’s parent and subsidiary companies are not held responsible for any damage for any modification of the batteries, chargers, devices and other products that we carry in any form or shape, this is including pack making.

ElementVape.com and any or all of ElementVape.com’s parent and subsidiary companies will not be held responsible or liable for any injury, damage, or defect, permanent or temporary that may be caused by the improper use of a Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable battery/batteries as well as chargers. Please have a greater understanding of the batteries/chargers you are using and how to care for them properly.

When working with Li-ion (Lithium-ion), LiPo (Lithium-ion Polymer) and any rechargeable cells, please be cautious and carefully use as they are very sensitive to charging characteristics and may explode or burn if mishandled. Please make sure that you have great knowledge on all rechargeable batteries before you use them. Always charge batteries at the clean and fire-proof surface. Never leave charging batteries unattended. If you see that there are visible damages on the batteries, please do not use. Always keep, store and transport the rechargeable cells in a safe, non-conductive container in controlled environment

Do not use any rechargeable battery as well as any battery charger if any visible damage is present, as well as if the cell or charger has been stressed through mishandling, accidental or otherwise, even if damage may not be visible. Always store and transport rechargeable cells in a safe, non-conductive container in a controlled environment. Please dispose battery cells, chargers or any other electronic devices in accordance of local laws and mandates. 

eGo AIO Pro C

eGo AIO Pro C, being all-in-one style, attaches the best anti-leaking structure with 4ml e-juice capacity. It’s powered by single replaceable 18650 battery. Large airflow inlet can be achieved directly from both sides. It is simple and convenient in use, but fashionable in look of several mixed colors and indicator light of seven colors. Its simplicity and efficiency make eGo AIO Pro C quite popular and unique.
Standard Configuration:
1 * eGo AIO Pro C Battery
1 * BF SS316-0.5ohm DL.
1 * BF SS316-0.6ohm MTL.
2 * Mouthpiece
1 * USB Cable
1 * Quick Start
1 * Warranty Card
Product Parameters:
Diameter: 22mm
Length: 145.5mm
Atomizer capacity: 4.0ml
Color: Silver, Black, White, Red, Blue, Orange
All-In-ONE Style
eGo AIO Pro C applies all-in-one style with atomizer inserted inside, which is quite convenient to use and carry.
Though petite but it is powerful enough to produce large vapor.
Interchangeable Battery Structure
Simply unscrew the battery bottom cover and put one 18650 cell into the body.
We kindly recommend high-rate 18650 cells with rated discharge current 25A.
Top Filling And Top Airflow Control
The improved airflow control system allows larger airflow inlet directly from both sides. Simply rotate the airflow ring clockwise or counter-clockwise to adjust the airflow inlet.
E-juice filling can be easily achieved by removing the top cap and injecting through the two side holes (not the vent pipe) directly.
Choose Your Color
In power-off condition, long press the fire button to turn off the indicate light or switch
Charging
Simply charge eGo AIO Pro by connecting it with a computer or a wall adapter via USB cable.
When it’s fully charged, the button light will go out.